HIP1011AEVAL1【PDF 1/11 页】EVAL BOARD PCI HOT PLUG HIP1011

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录1219

[1页]2页 3页 4页 5页

HIP1011A

Data Sheet

November 16, 2004

FN4631.5

PCI Hot Plug Controller

The HIP1011A is the second PCI Hot Plug Voltage bus

control IC from Intersil. A drop-in alternative to the widely

used HIP1011, the HIP1011A has the same form, fit and

function but additionally features an adjustable latch-off time

of the MOSFET switches and fault reporting.

Like the HIP1011, the HIP1011A creates a small and simple

yet complete power control solution with discrete power

MOSFETs and a few passive components. Four

independent supplies are controlled, +5V, +3.3, +12V, and

-12V. The +12V and -12V switches are integrated. For the

+5V and +3.3V supplies, overcurrent (OC) protection is

provided by sensing the voltage across external current-

sense resistors. For the +12V and -12V supplies OC

protection is provided internally. In addition, an on-chip

reference is used to monitor the +5V, +3.3V and +12V

outputs for undervoltage (UV) conditions. The PWRON input

controls the state of the switches. During an OC condition on

any output, or a UV condition on the +5V, +3.3V or +12V

outputs, a LOW (0V) is asserted on the FLTN output and all

MOSFETs are latched-off. The time to FLTN signal going

LOW and MOSFET latch-off is determined by a single

Features

? Adjustable Delay Time for Turn-Off and Fault Reporting

? Controls All PCI Supplies: +5V, +3.3V, +12V, -12V

? Internal MOSFET Switches for +12V and -12V Outputs

? μ P Interface for On/Off Control and Fault Reporting

? Adjustable Overcurrent Protection for All Supplies

? Provides Fault Isolation

? Adjustable Turn-On Slew Rate

? Minimum Parts Count Solution

? No Charge Pump

? Pb-Free Available (RoHS Compliant)

Applications

? PCI Hot Plug

? CompactPCI

Ordering Information

capacitor from the FLTN pin to ground. This added feature

allows the system OS to complete housekeeping activities in

preparation for an unplanned shut down of the affected card.

The FLTN latch is cleared when the PWRON input is toggled

low again. During initial power-up of the main VCC supply

PART NUMBER

HIP1011ACB

HIP1011ACBZA

(See Note)

TEMP. RANGE

( o C)

0 to 70

PACKAGE

16 Ld SOIC

(Pb-free)

PKG.

DWG. #

M16.15

(+12V), the PWRON input is inhibited from turning on the

switches, and the latch is held in the Reset state until the

VCC input is greater than 10V.

HIP1011ACB-T

HIP1011ACBZA-T

(See Note)

0 to 70

Tape and Reel

Tape and Reel (Pb-free)

User programmability of the overcurrent threshold, fault

reporting response time, latch-off response time and turn-on

slew rate is provided. A resistor connected to the OCSET pin

programs the OC threshold. A capacitor may be added to the

FLTN pin to adjust both the delay time to reporting a fault

and the latch-off of the supplies after an OC or UV event.

Capacitors connected to the gate pins set the turn-on rate. In

addition the HIP1011A has also been enhanced to tolerate

spurious system noise.

NOTE: Intersil Pb-free products employ special Pb-free material sets;

molding compounds/die attach materials and 100% matte tin plate

termination finish, which are RoHS compliant and compatible with

both SnPb and Pb-free soldering operations. Intersil Pb-free products

are MSL classified at Pb-free peak reflow temperatures that meet or

exceed the Pb-free requirements of IPC/JEDEC J STD-020C.

Pinout

HIP1011A

(SOIC)

TOP VIEW

M12VIN

FLTN

3V5VG

V CC

12VIN

3VISEN

3VS

16 M12VO

15 M12VG

14 12VG

13 GND

12 12VO

11 5VISEN

10 5VS

OCSET

PWRON

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.

1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc.

All other trademarks mentioned are the property of their respective owners.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式